#268-verA: Demo of LED Voltage Regulator Board Build - Paradise & Pacific O-Ga. MRC in Scottsdale AZ
* This video by Ron Smith demonstrates how to build an LED Voltage Regulator Board.
A. ~~~~~~ CONTENTS: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* Overview of Parts: 0:30 min
1 Bridge rectifier: 0:54 min
. (put squiggle signs to right)
. (hold soldering iron about 2 sec each joint)
2 Potentiometer: 2:16 min
. (2 legs toward rear {circular outline for capacitor})
3 Capacitor: 3:30 min
. (long leg plus, twist slightly)
4 Choke: 4:20 min
. (silver stripe towards front)
. (bend legs 90 deg, tighten with pliers)
5 Resistor: 5:40 min
. (can go either way) (bend legs 90 deg)
6 Voltage regulator: 6:48 min
. (metal stand goes toward rear)
. (put top of voltage regulator in clamp, solder center leg first
7 Small JST connector -- DC out: 7:58 min
. NOTE: This connector was soldered "off camera"
. (red towards front on "+" terminal)
(put connector wires in clamps to hold)
8 Big JST connector -- AC in: 8:20 min
. (red towards front on "+" terminal)
9 Test - connect to LED strip for testing: 9:14
. The END: 10:41
B. ~~~~~~~~~~~~~~~~~~~ LINKS ~~~~~~~~~~~~~~~~~~~~~|
* Google Drive photo album showing images used in this video: https://drive.google.com/open?id=1pH9VenT8tFZ4roUVqnjBmtFCb3ABf4Fz
* Paradise & Pacific Railroad Club: http://PandPrr.com
* McCormick-Stillman Railroad Park: http://TheRailroadPark.com
~~~~~~~~~
This iMovie10 video was uploaded for Paradise & Pacific Railroad Club by http://JamesIngram.net .
This video is linked from the "temporary links page" at http://pandprr.wordpress.com .
A. ~~~~~~ CONTENTS: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* Overview of Parts: 0:30 min
1 Bridge rectifier: 0:54 min
. (put squiggle signs to right)
. (hold soldering iron about 2 sec each joint)
2 Potentiometer: 2:16 min
. (2 legs toward rear {circular outline for capacitor})
3 Capacitor: 3:30 min
. (long leg plus, twist slightly)
4 Choke: 4:20 min
. (silver stripe towards front)
. (bend legs 90 deg, tighten with pliers)
5 Resistor: 5:40 min
. (can go either way) (bend legs 90 deg)
6 Voltage regulator: 6:48 min
. (metal stand goes toward rear)
. (put top of voltage regulator in clamp, solder center leg first
7 Small JST connector -- DC out: 7:58 min
. NOTE: This connector was soldered "off camera"
. (red towards front on "+" terminal)
(put connector wires in clamps to hold)
8 Big JST connector -- AC in: 8:20 min
. (red towards front on "+" terminal)
9 Test - connect to LED strip for testing: 9:14
. The END: 10:41
B. ~~~~~~~~~~~~~~~~~~~ LINKS ~~~~~~~~~~~~~~~~~~~~~|
* Google Drive photo album showing images used in this video: https://drive.google.com/open?id=1pH9VenT8tFZ4roUVqnjBmtFCb3ABf4Fz
* Paradise & Pacific Railroad Club: http://PandPrr.com
* McCormick-Stillman Railroad Park: http://TheRailroadPark.com
~~~~~~~~~
This iMovie10 video was uploaded for Paradise & Pacific Railroad Club by http://JamesIngram.net .
This video is linked from the "temporary links page" at http://pandprr.wordpress.com .
Category
🤖
Tech