Setting tubeless up on road bikes can be a tricky process and there are a lot of mistakes that can be made. However, Sam Gupta has taken his years of experience as a mechanic to share all his knowledge on how to successfully set up a tubeless system on your road bike. Starting at the very beginning, all of these top tips for setting up tubeless will mean that hopefully you can get it done right first time round.
Category
🥇
SportsTranscript
00:00 I'll be honest, ever since tubeless tech made its way onto road bikes, I was never a fan. It felt
00:05 like the same products that were being used in the mountain bike world were just being repackaged and
00:10 marketed to road bike users. The issue being that the requirements of the two different disciplines
00:16 are actually pretty different. During my time working as a mechanic, I also saw all the problems
00:21 that the technology was causing people, from simply trying to get it set up in the first place,
00:26 to blowouts, to then punctures that just wouldn't seal. In fairness, being a mechanic does mean
00:32 you're always left to pick up the pieces and maybe not seeing all the times that the technology is
00:37 actually working. So this may have pushed my bias further into the extreme. As reluctant as I was,
00:44 I have now ridden a fair few bikes with tubeless setups. So I'm going to pair that experience with
00:49 all the time that I spent setting up other people's tubeless systems to let you know everything that I
00:55 wish I knew at the very start. I'm going to start at the very top because before anyone gets anywhere
01:05 close to leaving their inner tubes at home, we need to make sure that we've sourced all of the
01:10 correct components. We have actually made an entire video comparing some of the most popular sealants
01:15 on the market, so you can go and give that a watch to work out which sealant you would want to use.
01:20 In this instance though, I'm going to be using this, the Stans sealant. I've also got some pretty
01:25 standard valves and I'll be using these Paneracer Agilis TLR tyres. And then for the wheels,
01:32 we have got the Hologram R45 wheels from Cannondale. Luckily, these wheels are actually
01:38 tubeless ready because they have the tape pre-installed. Now one of the key things that
01:44 you don't want to get wrong at the very start is actually your tyre selection. Even though you can
01:48 set up tubeless with narrower tyres, I would always opt for something that's kind of 28c as a minimum.
01:56 As we know from the gravel and mountain biking world, tubeless works best at lower pressures.
02:01 And I'm sure there's a whole bunch of you that have been running tubeless setups on 25c tyres
02:06 and you maybe haven't had any issues, but I would potentially put this down more to luck
02:11 than anything else. If you want to make sure that you're giving your sealant the best chance
02:16 possible at doing its job, then go wide on your tyres so that you can run a lower pressure.
02:21 It's pretty well known that tubeless tyres can be a complete nightmare to get onto your rims.
02:32 It can almost leave you feeling like you'll never be able to stretch them on. You can end up with
02:37 blood blisters, sore hands and not to mention just feeling incredibly demoralised. But there are a
02:43 few things that you can do to make life a little easier when it comes to getting them onto that rim
02:49 for the very first time. Before you try and actually get them onto the rim, what I would say is
02:54 place your new tyres somewhere warm overnight. Ideally, maybe next to a radiator as that is
03:01 going to help the rubber become more malleable. Then if you have an older set of wheels,
03:06 try fitting the tyres to these first with an inner tube and stretch them out a bit. Now of course,
03:11 sometimes older wheels which aren't made for tubeless setups can be a little easier to mount
03:16 tyres to, but this can be a little bit hit and miss. So don't worry if it doesn't work out.
03:22 If however, you can get the tyres on, again I would say leave them inflated with that inner tube,
03:27 again in a warm place and it's just going to make those tyres a little bit easier to manage.
03:36 Getting your tubeless wheels ready and prepared is absolutely crucial before you can even think
03:41 about trying to get them set up. First, make sure that they're incredibly clean. You don't
03:46 really want any gunk left from any previous tubeless setups. Also, check the rims for any
03:52 dents or dings which could hinder the ability for the tyre to seat properly. Make sure that the rim
03:58 tape is tight and evenly covering the inside of the rim. And make sure that your valve is inserted
04:04 correctly and it's right in the bed of the rim and potentially in the correct direction if it
04:10 needs to be. Also, just make sure you utilise the little o-ring on the valve as well. You'd be
04:16 amazed at how often these little o-rings can actually make a huge difference to getting your
04:21 tyre seated first time. If you're reusing valves, then pull the cores out and ensure that they're
04:26 clean and they aren't gunked up on the inside. Once you've got your wheels prepped, then,
04:35 without getting any sealant involved, try and mount the tyres. As always, be sure to utilise
04:41 the deepest part of the wheels to ensure that you get the maximum amount of leverage. And just
04:47 slowly work it all the way round. If you are able to get the tyres on from this point, then great.
04:52 Get them inflated and see if you can get those tyres to pop into the bead.
04:56 If you can't get the tyres onto the rim, then actually there are tools that can help you,
05:05 like one of these tyre grabbers. Now, you can get these from places like Brand X,
05:10 Lifeline or Challenge. They simultaneously hook onto the rim and grab the edge of the tyre. And
05:16 then as you squeeze, it will then manoeuvre it into place. Now, as you keep working it around,
05:22 you should be able to get it on. But don't be shy about putting a fair bit of force through
05:26 one of these. They can absolutely save your hands so much pain. And actually,
05:31 they are built to take a fair bit of strain.
05:33 If you've successfully completed a dry fit on your wheels, and if your sealant is fairly runny,
05:43 then you can remove the valve core and inject the sealant directly into the wheel
05:47 and then simply re-inflate. However, if your sealant is a bit too thick and would just coagulate
05:53 inside the valve, then pop off a small section of the tyre, pour in the correct amount of sealant,
05:58 and then spin the wheels by 180 degrees and then work the tyre back into place.
06:02 There's always one part of the tubeless setup process which always has my nerves on edge,
06:11 and that is when you start to introduce air for the first time to get the tyre to seat.
06:16 Just remember that the pop
06:18 is your friend. And what I like to do to save myself from the dreaded tubeless explosion
06:27 is to get the tyre to pop into place using a compressor or track pump with a recharge facility
06:33 and then finish it off with a hand pump to fine tune that pressure inside the tyre.
06:43 This leads me really nicely onto my next point, and that's to make sure that you monitor the
06:47 pressure that is going into your tyres. You may be very used to the amount of air you've been
06:52 filling your inner tubes with, however, tubeless tyres and hookless rims do have some pretty
06:58 different requirements. A lot of tubeless tyres and hookless rims have a maximum pressure of around
07:04 70 psi. Of course, be sure not to exceed any maximum recommended pressure, but more importantly,
07:11 make sure the pressure is right for your combined bike and rider weight. This is how you can start
07:16 to reap the benefits of running a more comfortable, fast-rolling tyre setup. I like to use the SRAM
07:22 calculator to help me work out what pressure I should be putting into my tyres.
07:27 One of the things that I really started to hate about tubeless setups, especially during my time
07:36 as a mechanic, was the issues caused when the system went wrong. And I must say that the time
07:42 that my tubeless setup went wrong, well, it was a complete and utter nightmare. I had to fight with
07:48 a tight-fitting sealant-covered tyre to drain out the remaining sealant to then try and fit an inner
07:54 tube, which in reality was like trying to wrestle a wet fish into a small hole. However, the mistake
08:00 that I made was that I wasn't carrying any bacon strips or plugs to fill the hole that the sealant
08:05 couldn't deal with. I think that if I had some of those, then I probably could have sorted out the
08:10 tyre fairly easily. So, don't be like me. Make sure you're carrying the necessary tools to fix
08:17 the basic problems. I won't lie to you, I'm still pretty sceptical about running tubeless on the
08:24 road. For me, simply replacing or repairing an inner tube, compared to wrestling with a tight-fitting
08:30 sealant-covered tyre when a puncture just won't seal, is still my preferred option. However,
08:36 I think if you ensure you carry the right tools with you, you fit tyres with a nice large volume,
08:41 and utilise quality sealant, and also run the right pressure for your bike and rider weight,
08:46 well, you might just be okay. Is there anything though that you wish you knew before you went
08:52 tubeless? Let me know down in the comments below. If you enjoyed the video, then please do drop it
08:57 a like, subscribe to the channel for more content, and I'll see you again very soon.
09:02 (whooshing)
09:04 [BLANK_AUDIO]