ZEBRONICS BT3440RUCF Speaker Socket Replace, output spkr sokit बदलना सीखे s.k electronic's work
Category
😹
FunTranscript
00:00Hello friends, welcome to skelectronics.com
00:03So, I have a home data of Jabronix
00:06Its speaker socket, output encryptor's pin is completely damaged
00:11The pin is broken inside
00:13We can remove it, but someone has put it inside
00:18He has turned it all around and has broken it inside
00:21And it is not coming out
00:22So, we will replace it
00:24So, I have this home data
00:26You have seen its model number
00:28Jabronix BT3440RU-CF
00:34This is its model
00:36It is 2.1
00:37So, see the problem
00:39Two or three pins are broken inside
00:41And it is in a very bad condition
00:43Otherwise, someone removes it
00:44It is a very easy way to remove it
00:45I will tell you how to remove it
00:46Friends, why am I making a video on changing it
00:49Because it is a little different
00:50See, it is not even open yet
00:52I know, but it must be on the board
00:57This socket must be on the board
00:59Because most of the original company's home data
01:01The socket of the speaker output is connected to the board
01:06So, I have opened all the pages of this
01:08I will not waste your time
01:10So, see this is our board
01:12It has only IC
01:13There are 20-25 small ICs
01:15It has no TDI, 20-30 ICs
01:18So, see we will remove the jigs from here
01:21Jig is stuck
01:22Jig is stuck from the bond fix
01:25So, friends, watch the video till the end
01:27Only then you will understand
01:29If you are new to my channel, then you can subscribe here
01:32You will get such a good video
01:34That you will say, yes, sir, it is very good
01:36So, you will get a real video
01:37So, see in this
01:38Zero 12 transformer has been used
01:41There are only two wires in the secondary
01:45So, first we will open the page of this
01:47Which has a page in it
01:49There is only one page in it
01:50The board is also blocked
01:53The socket is also blocked
01:55So, it will not move like this
01:56So, we will see once
01:58There is glue here, see
01:59We will remove this glue
02:01Means remove it from here
02:03So, I removed a little
02:05So, I went up the board
02:06So, it came out, see
02:08There is an antenna wire in it
02:10Let's remove this antenna wire
02:12This iron is not a little hot yet
02:15I just put it right now
02:17So, I remove it
02:20So, it is removed
02:22So, see
02:23This is the socket of our output speaker
02:25So, we will put new
02:27See, it is very easy to put new
02:29Your print will not burst
02:30And your board will also get stuck
02:33It will get stuck like this
02:34You will not even know
02:35Whether you have changed it or not
02:37So, see
02:38This is a 4 pin socket
02:40This is 4RC
02:42We will call it 4RC socket
02:44Okay, so this is our socket
02:46We have to put it in this
02:47So, how will we put it
02:48So, see
02:49We have to keep the direction
02:51As it was in it
02:53So, first of all
02:55We will hold the board from one side
02:57So, I got it caught
02:59From one of my boys
03:01So, we have to do it like this
03:03By holding it like this
03:05So, you must have seen this trick for the first time
03:07Or you must have seen it
03:08So, do it once and see
03:09What happens with this
03:10The soldering is removed very well
03:12The soldering is removed very well
03:14And your print does not burst
03:16What happens with shield wire
03:17What happens with shield wire
03:18Sometimes the print also bursts
03:19So, keep it like this
03:20And rub it like this
03:22The old solder will come off
03:24So, your wire
03:26I will show you very well
03:28By zooming you once
03:30So, see
03:32In this way, all the soldering is removed
03:34This socket has gone all the way up
03:36See how easily it came out
03:38So, if you like this method
03:40Then do like the video
03:42So, see
03:44Normally
03:45Now, we will put it
03:47Like our new socket
03:49Soldering the new socket is the same
03:51As we normally do
03:53And after soldering
03:55Do it in such a way
03:57That it is not judged
03:58Whether your work is done or not
04:00Because
04:01The cleaner you do the soldering
04:03The cleaner you do the work
04:05Your work will be better
04:07Okay
04:08Do the work well
04:09Do the electronics work cleanly
04:11So, your name will be
04:13Okay
04:14So, see
04:15I did the soldering here
04:16And from the chimney
04:17Here I am doing this
04:18That there is no sorting here
04:20Or soldering etc
04:21There will be no pin wire etc
04:23So that our sorting does not become
04:25These problems are created
04:26We changed the socket
04:27After that
04:28Humming is coming
04:29Or it is coming
04:30This problem is created then
04:31So, use a little thinner or petrol here
04:33And clean it with a brush
04:35Now
04:36So, you can see
04:37It has become like this
04:38That in this
04:39Maybe something has not been replaced yet
04:41So, it became like a new board
04:43And we removed all the pastes from it
04:45So, it is completely set
04:47See, it is completely new
04:48So, now you have to pay special attention to one thing
04:50When you change such a socket
04:51There is a rubber attached to it
04:53This one
04:54So, you must apply this rubber
04:56If you do not apply this rubber
04:57So, with it
04:58When your hummer buffer will play
05:00Air will pass
05:01What will happen in that
05:02Your base will burst
05:03So, you will say
05:04Sir, you will tell me in the comment
05:05Sir, our base is bursting
05:07We changed that thing
05:08So, you will leave this
05:10You will break
05:11This will happen only
05:12Otherwise, you will not have
05:14If you do not have
05:15You still want to install
05:17So, you can pack it with glue on the side
05:19Means after installing the socket
05:21When you sell
05:22So, pack it with glue on the side
05:24So, in this way
05:25See, I have packed it now
05:27As it was normally
05:29Now, I will install it again in the same
05:31So, I will not waste your time
05:33I have installed
05:34See, the jigs etc
05:35And I
05:36The jansi jig
05:37From where it is installed
05:38Did not remove
05:39Remove it from there
05:40And put it there
05:41If you do not understand
05:42Which one to remove
05:43So, first you take a photo of it
05:45Or put a coat on it with a pen
05:47Or put a coat with a marker
05:48So, this is a better way
05:49So, let's put all the pages of it
05:51By the way, we are
05:52We know everything
05:53So, let's put all the pages of it
05:54Then I will show you
05:58So, now we will check it
06:00So, I am putting a socket here
06:02Increase its volume a little
06:04I have turned on
06:05We are putting bluetooth
06:07So, here we have turned on
06:09And the sound is also coming
06:11So, the volume is making a lot of trouble
06:13Now I will change the volume
06:14But I will not make the video so long
06:17So, see friends
06:18All these are working
06:19Because there will be two easy outputs
06:21For two inputs
06:22So, the lower output
06:23So, it is working
06:24So, that's all for today
06:25Like the video
06:26That's all for today
06:27Jai Hind, Vande Mataram