Leica TS11 Total Station ka istemal karte hue As-Built aur Point Marking (Stake Out) karne ka tareeqa kuch yun hai:
Step-by-Step Guide:
1. Total Station ko Setup karna:
Sab se pehle Total Station ko tripod par rakhein aur isay center karein.
Leveling screws ki madad se isay bilkul hamwar (level) karein.
Phir Total Station ko janchne ke liye Backsite point par nazar karein aur isay horizontal zero par set karein.
2. As-Built Survey karna:
As-Built ka matlab hai ke aap existing structure ya feature ko janch kar uske coordinates hasil karein.
Total Station ke Measuring Mode mein jayein.
Jo point measure karna hai, us par Total Station ka Telescope rakhain.
Measure button ko dabayein.
Total Station us point ke Coordinates (Northing, Easting, Elevation) faraham karega.
In Coordinates ko note karein ya Save karein.
3. Stake Out ya Marking a Point:
Stake Out karne ka maqsad mojooda naqshay ya plan ke mutabiq kisi khaas jagah par marking karna hai.
Stake Out Mode ko Total Station mein select karein.
Jis point ko aap mark karna chahte hain uska Coordinate (Northing, Easting, Elevation) darj karein.
Total Station aap ko bataye ga ke is point tak pohanchne ke liye aap ko kitna aur kis simt mein harkat karni hai.
Telescope ko us maqam par le jayein.
Jaise hi aap matlooba maqam par pohanch jayein, point ko zameen par mark karein.
4. Points ki Verification:
Is baat ko yaqini banayein ke mark kiye hue points bilkul durust jagah par hain. Dobara measure karke check karein.
Izafi Tips:
Data Transfer ke liye aap USB ya Leica software istemal kar sakte hain taake tamam measured data ko mehfooz kar sakein.
Battery ki haalat ka khayal rakhein taake field mein koi masla na ho.
Note:
Aap ke specific kaam aur project ki zarooriyat ke hisaab se mukhtalif modes aur settings bhi istemal kiye ja sakte hain.
Step-by-Step Guide:
1. Total Station ko Setup karna:
Sab se pehle Total Station ko tripod par rakhein aur isay center karein.
Leveling screws ki madad se isay bilkul hamwar (level) karein.
Phir Total Station ko janchne ke liye Backsite point par nazar karein aur isay horizontal zero par set karein.
2. As-Built Survey karna:
As-Built ka matlab hai ke aap existing structure ya feature ko janch kar uske coordinates hasil karein.
Total Station ke Measuring Mode mein jayein.
Jo point measure karna hai, us par Total Station ka Telescope rakhain.
Measure button ko dabayein.
Total Station us point ke Coordinates (Northing, Easting, Elevation) faraham karega.
In Coordinates ko note karein ya Save karein.
3. Stake Out ya Marking a Point:
Stake Out karne ka maqsad mojooda naqshay ya plan ke mutabiq kisi khaas jagah par marking karna hai.
Stake Out Mode ko Total Station mein select karein.
Jis point ko aap mark karna chahte hain uska Coordinate (Northing, Easting, Elevation) darj karein.
Total Station aap ko bataye ga ke is point tak pohanchne ke liye aap ko kitna aur kis simt mein harkat karni hai.
Telescope ko us maqam par le jayein.
Jaise hi aap matlooba maqam par pohanch jayein, point ko zameen par mark karein.
4. Points ki Verification:
Is baat ko yaqini banayein ke mark kiye hue points bilkul durust jagah par hain. Dobara measure karke check karein.
Izafi Tips:
Data Transfer ke liye aap USB ya Leica software istemal kar sakte hain taake tamam measured data ko mehfooz kar sakein.
Battery ki haalat ka khayal rakhein taake field mein koi masla na ho.
Note:
Aap ke specific kaam aur project ki zarooriyat ke hisaab se mukhtalif modes aur settings bhi istemal kiye ja sakte hain.
Category
📚
Learning